Skip to content
CA Unified Infrastructure Management Probes
Documentation powered by DocOps

How To Videos

Last update May 11, 2018

Contents

Probe Deployment with Admin Console

A new version of Admin Console was introduced with CA UIM 8.4.7. To learn how to install probes in the local archive with the Admin Console interface on a CA UIM 8.4.7 or later system, watch the Probe Deployment with Admin Console Introduced with CA UIM 8.4.7. To learn how to install probes in the local archive with the Admin Console interface on a CA UIM 8.4 or earlier system, watch the Probe Deployment with Admin Console Introduced with CA UIM 8.4.

CA UIM 8.4.7 and later

In this video, we show you how to deploy a probe using the Admin Console interface. This scenario shows the steps for downloading and then installing a probe package on a robot.

CA UIM 8.4 and earlier

In this video, we show you how to deploy a probe using the Admin Console interface. This scenario shows the steps for downloading and then installing a probe package on a robot.

Default Monitor Templates

In this video, we show you how to use the probe Template Editor to apply a default monitor template. You can use default templates to quickly configure the monitors and alarms for probe Unified Dashboards in CA UIM.

Monitor Template Filters

In this video, we show you how to use the probe Template Editor to configure monitor template filters. I will create a new template and demonstrate how to use filters to apply an alarm and a Quality of Service data point to a specific group of components.

Manage Configuration Profiles with Monitoring Configuration Services

Watch the Device Monitoring with MCS video to get started with the Monitoring Configuration Service and create a configuration profile for a single device in your CA UIM 8.4 or later environment. After testing the configuration applied to a probe and reviewing the alarms and metrics the probe generates, watch the Group Monitoring with MCS video to learn how to copy a tested device configuration profile to a USM group. When you upgrade to CA UIM 8.5.1, watch the Update MCS Templates video to learn how to update templates with configuration profiles to newer versions.

Device Monitoring with MCS

In this video, we show you how to use Monitoring Configuration Service (MCS) in CA UIM to create monitoring configuration profiles. MCS applies these profiles to target devices and deploys probes as needed.

Group Monitoring with MCS

In this video, we show you how to use Monitoring Configuration Service (MCS) in CA UIM to copy a tested monitoring configuration profile to a group of devices. MCS applies the copied profile to all the devices in the group, and deploys probes as needed.

Update MCS Templates

In this video, we show you how to update templates with configuration profiles to newer versions after you upgrade to CA UIM 8.5.1.

Troubleshooting the aws Probe Configuration

In this video, we show you how to troubleshoot the aws probe configuration. This scenario shows the creation of a profile in the probe configuration GUI and provides some basic troubleshooting tips.

Multi-UMP Configuration

This video shows you how to use how to configure multiple UMP servers in a CA UIM environment.

Configure Load Balancing for UMP

This video shows you how to use how to configure load balancing in a dual UMP environment.

Create a Tunnel Server and Tunnel Client with Admin Console

This is a series of four videos. In these videos, you learn how to create a tunnel server and tunnel client in Admin Console as well as platform specific post-creation tasks.

Create a Tunnel Server and Tunnel Client with Admin Console - Part 1

This is part one of a series of four videos. In this video, you learn how to create a tunnel server using Admin Console.

Create a Tunnel Server and Tunnel Client with Admin Console - Part 2

This is part two of a series of four videos. In this video, you learn how to create the other side of the tunnel, known as the tunnel client, using Admin Console.

Create a Tunnel Server and Tunnel Client with Admin Console - Part 3

This is part three of a series of four videos. In this video, you learn how to perform the post-creation tasks for a Windows 2008 hub server to ensure that your hub to hub communications occur over the new tunnel and not over old static hub routes.


Create a Tunnel Server and Tunnel Client with Admin Console - Part 4

This is part four of a series of four videos. In this video, you learn how to perform the post-creation tasks for a Redhat Linux hub server to ensure that your hub to hub communications occur over the new tunnel and not over old static hub routes.


Create a Queue with Admin Console

This video shows you how to create a queue between two hubs using Admin Console.

Create a Tunnel Server and Tunnel Client with Admin Console for CA UIM 8.47

This is a series of two videos. If you have installed or upgraded to CA UIM 8.47, use these videos to learn how to create a tunnel server and tunnel client in Admin Console. If you are running CA UIM 8.4 or earlier, watch this video series.

Create a Tunnel Server and Tunnel Client with Admin Console - Part 1

This is part one of a series of three videos. In this video, you learn how to create a tunnel server using Admin Console for CA UIM 8.47.

Create a Tunnel Server and Tunnel Client with Admin Console - Part 2

This is part two of a series of two videos. In this video, you learn how to create the other side of the tunnel, known as the tunnel client, using Admin Console for CA UIM 8.47.

Create a Queue with Admin Console for CA UIM 8.47

This video shows you how to create a queue between two hubs using Admin Console for CA UIM 8.47. If you are running CA UIM 8.4 or earlier, watch this video.

Introduction to CABI for UIM

This video show you how to install and access the pre-defined CABI for UIM dashboards and the CABI Server application on a CA UIM 8.47 system.

Note: CA UIM v8.47 is the minimum required version.

Creating CABI for UIM Dashboards

This video show you how to create a custom CABI for UIM dashboard in the CABI Server application and then add the dashboard to UMP on a CA UIM 8.47 system.  The video focuses on features that are specific for displaying CA UIM data in a CABI for UIM dashboard.

Note: CA UIM v8.47 is the minimum required version.


Enable sap_basis Probe Communication With the SAP Server

In this video, demonstrate how to install the SAP Java Connector library on a Windows system.

License Management in Admin Console

In this video, we show you how to manage your CA UIM licenses using the Admin Console. The process shown in this video was introduced with CA UIM version 8.4.7.

 

Configure HTTPS

In this video, we provide you with an overview of the various ways you can enable SSL encryption for users in CA UIM.

 

Configure nas

The following videos show you some of the ways in which you can configure the nas probe.

Create an Email Auto-Operator

In this video, we show you how to configure a basic email Auto-Operator.

Managing Sustained Alarms

In this video, we show you how to configure an Auto-Operator to manage sustained alarms.

When to Deploy Multiple nas Probes

In this video, we show some example scenarios for deploying more than one nas probe in your CA UIM environment.

Configure Alarm Forwarding and Replication

In this video, we show you how to forward alarms from a remote nas to a primary nas.

Update Device Vendor Certifications for the snmpcollector Probe

In this video, we show you how to update device vendor certifications for the snmpcollector probe.

Setup and Use Provance Gateway Probe

In this video, we should you how to setup and use the Provance Gateway probe.



Was this helpful?

Please log in to post comments.